GLEASON- PFAUTER P 1200 S

•  
  Reference number 1058-E23259

  Manufacture Year 2008

  Operation Hours not applicable

• Vendor

  EMUK GmbH Werkzeugmaschinen
  Siemensstraße 24a
  76316 Malsch

  Germany

  

• Main Category

  Metal working machines

• Category

  Gear Cutting Machines

• Type of Machine

  GEAR SHAPERS

• Sort of Machine

  Gear Shapers

• Manufacturer

  GLEASON- PFAUTER

• Control

  Siemens 840D Powerline

• Technical data

  max. wheel diameter

  1200 mm

  gear width

  350 mm

  max. module

  16

  min. module

  0,5

  max. workpiece diameter

  1400 mm

  table diameter

  1200 mm

  table hole

  300 mm

  control

  Siemens 840D Powerline

  total power requirement

  75 kW

  weight of the machine ca.

  24 t

  dimensions of the machine ca.

  5x3x3,8 m

• Description

  Gleason-PFAUTER CNC gear shaping machine P 1200 S for the production of
  internally and externally cylindrical gears with internal and external teeth
  and other rolling profiles and moulds profiles and moulds that regularly occur
  on the cylindrical workpiece circumference and for the production of profiles
  in the single part process.
  
  Special version with hydraulic shaping head H1
  
  SCOPE OF EQUIPMENT:
  
  - Basic machine P1200S, Siemens 840D Powerline (XP)
  - Hydraulic shaping head H1
  - Signal light (3-colour)
  - Extended software for fault diagnosis
  - Telephone diagnosis system
  - Chip disposal through table bore
  - Set of adjusting wedges
  - Monitoring devices
  - Warm-up programme
  - Network connection (Ethernet)
  - 19" flat control panel OP 015A
  - Offline version "dialogue programming
  - Vapour separator make "3nine" type KLARA
  - Machine installation under floor
  - Rinsing gun
  - Mounting device
  - Cutting wheel holder ( 3 pieces )
  - Cutting wheel holder for sheep cutting wheels
  - Cutting wheel holder for sheep cutting wheels
  - Special cutting wheel holder
  - Preparation for retrofitting paper belt filter system
  - Measuring device for machine P 1200 S
  - Clamping base body
  - BDE/MDE interface in the machine control cabinet
  Modification of vapour separator make "3nine" type Klara type EMMA
  
  Working range and technical data:
  
  Nominal workpiece diameter
  External toothing. . . . . . . . 1.200 mm
  Internal gearing. . . . . . . . 1.200 mm
  
  Largest workpiece circulation Ø without counter stand... 1.400 mm
  
  Nominal machine module approx.
  - with hydraulic impact head H1... 16 mm
  
  Shaping spindle stroke rate range
  - with hydraulic shaping head H1 max. 80 min-1
  
  Largest toothing width
  - with hydraulic shaping head H1... 350 mm
  
  Smallest pitch height of the hydrostatic screw guide
  - with hydraulic shaping head H1... 850 mm
  
  Smallest/largest distance between tool and workpiece axis
  - with hydraulic shaping head H1... 0 - 750 mm
  
  Axial slide adjustment range - with hydraulic shaping head H1... 1.100 mm
  Lowest shaping spindle position above table with hydraulic shaping head H1
  ** with upper position Shaping stroke... 560 mm
  
  Column side offset range - with hydraulic pusher head H1... +/- 50 mm
  Mould mounting cone - with hydraulic shaping head H1
  - HSK-80(hollow shank taper according to DIN 69063)
  
  Workpiece with external gearing:
  - Module max. 16 mm,
  - max. toothing width 350 mm,
  - max. external Ø 1.200 mm,
  
  Workpiece with internal gearing:
  - Module max. 16 mm,
  - max. toothing width 350 mm,
  - max. circulation Ø 1.400 mm,
  - max. internal Ø 1.200 mm,
  - max. shaping wheel Ø 260 mm,
  - Mounting in shaping spindle HSK-80,
  - Slide travel; X/Y/Z- 750 /100 / 1.100 mm,
  
  Workpiece table:
  - Outer Ø 1.200 mm,
  - bore 300 mm,
  - max. load 150 kN,
  - Cooling unit, Küma, type OWT600-3KK, year 2008,
  - Hydraulic unit, manufactured by Parka,
  - Centrifuge, made by Steimel,
  - Air filter, Indusa, type EL4001NTDASECL/O,
  version AOO, max. air capacity 4.000 m³/h
  
  
  This ad was created with MODUL MWS - the software solution of LogoTech.

• State

  Used